- PIC12C508,PIC12C509
- PIC12C508A,PIC12C509A
- PIC12CE518,PIC12CE519
- PIC12C671,PIC12C672,PIC12CE673,PIC12CE674
- PIC12F508,PIC12F509 The trick of programming PIC12F508/509 using IC-Prog
- PIC12F629,PIC12F635(1,2),PIC12F675,PIC12F683(2)
- PIC16C505
- PIC16C61,PIC16C62A,16C62B(3),PIC16C63,PIC16C63A
- PIC16C64A,PIC16C65A,PIC16C65B,PIC16C66,PIC16C67
- PIC16C620,PIC16C620A,PIC16C621,PIC16C621A,PIC16C622,PIC16C622A
- PIC16CE623,PIC16CE624,PIC16C625
- PIC16F627,PIC16F628
- PIC16F627A(2),PIC16F628A,PIC16F648A
- PIC16F630,PIC16F636(2),PIC16F676,PIC16F684(2),PIC16F688(2)
- PIC16C710,PIC16C711(3)
- PIC16C712,PIC16C716(3)
- PICPIC16C71,PIC16C72,PIC16C72A,PIC16C73A,PIC16C73B,PIC16C74A,PIC16C74B,PIC16C76,PIC16C77
- PIC16F72,PIC16F73,PIC16F74,PIC16F76,PIC16F77
- PIC16C745(3),PIC16C765(3)
- PIC16C717,PIC16C770,PIC16C771(7)
- PIC16C773,PIC16C774
- PIC16C781(7),PIC16C782
- PIC16C923,PIC16C924
- PIC16F818,PIC16F819
- PIC16F83
- PIC16C84
- PIC16F84
- PIC16F84A
- PIC16F87(2),PIC16F88
- PIC16F870(8),PIC16F871(8),PIC16F872,PIC16F873,PIC16F874(4),PIC16F876(5),PIC16F877(5)
- PIC16F873A(5),PIC16F874A(5),PIC16F876A,PIC16F877A
- PIC18F1320,PIC18F2320,PIC18F4320
- PIC18F242,PIC18F252,PIC18F442,PIC18F452
- PIC18F248,PIC18F258,PIC18F448,PIC18F458(3)
- PIC18F4539(3)
- Although programming is ended normally, after programming, there is a case which reading/verification from a device become impossible. Please feel easy. The program code is written in normally. Moreover, erasure and re-programming can normally.
- IC-Prog(1.05D) has not supported these devices yet. Please use WinPic.
- Since the programming voltage raise of "Multi PIC Programmer" is less than required value, these devices cannot enter the program mode. If MOS-FET is removed temporarily and VDD is always turned ON or it connects the gate and source of MOS-FET by test lead etc. or attaches a switch between a gate and GND, program writing will come to be performed normally.
- WinPic cannot program/verify/erase these devices with Multi PIC Programmer 5V2. Please use IC-Prog.
- IC-Prog cannot program/verify/erase these devices with Multi PIC Programmer 5V2. Please use WinPic.
- PIC 16C715 is a special device with a 16 bit/word length program memory and a config memory. Although this device is included in the supported devices list of WinPic and IC-Prog, they cannot program this device in practice. Moreover, if programming is tried, code protection bit will be set and applied to a blank device (If you intend to program expensive JW type PIC16C715,it will be impossible re-programming eternally even if after UV erasure!).
- These 20 pin devices have different pinout arrangement from other devices. Use ICSP method or use an adapter for programming these devices.
- These devices can be programmed well, but cannot be erased. For erasure these devices, use above mentioned method(3). If programming goes wrong, perform "Erase all" command by using IC-Prog beforehand.
Top view Schematic Bill of material PCB size is 100mmx37.5mm in the minimum
PCB Component layout PCB Layout Silk screen (mirrored image for direct toner transfer) Typical pin out for TO-92 Transistors Device Positions Courtesy of FENG3